Specifications:

1. Product Name: Resilia

2. Manufacturer

Floor Surfaces, Inc., P.O. Box 22934, Santa Barbara, CA 93117
Tel: 805-275-4087
Email: sales@floorsurfaces.com
Web: www.floorsurfaces.com

3. Product Description

Resilia Interlocking Floor Tiles designed to enable laying tiles quickly without adhesives on any firm, flat surface, using only a small roller, utility knife and common installation tools. When installed, the flooring has a stylish, uniform appearance. Because adhesives are NOT required, Resilia Tiles may be installed over old tiles, epoxy floors, moisture problem surfaces, or uncured concrete floors.

4. Applications

Retail Shops Garages Offices Warehouses Auto Service Areas

Retail Stores Schools Manufacturing Aircraft Hangers Health Clubs

Medical Offices Exhibition Halls Raised Access Floors Trains & Busses

5. Composition & Materials:

Injection molded, homogeneous, flexible PVC. (solid vinyl tile).

6. Size:

Size: 12" x 12"
Thickness: 1/4"
Weight: 1.25 lb per tile = 1.25 lb per sq. ft.

7. Limitations:

• Floor Surfaces Resilia^TM are not recommended for exterior outdoor applications, although in some cases they may be used in floors with single colors. However Floor Surfaces does not warrant the performance of its tiles for outdoor use.

  Resilia tiles are suitable for residential, commercial and industrial kitchens or bathrooms, however due to wetness and oil vapor conditions, Floor Surfaces specifically does not assume any liability regarding slip resistance in either dry, wet, grease, soapy or oil vapor conditions. Further the use of Resilia tiles or any other tiles used in kitchens, or any other applications are subject to slip conditions beyond our control due to oils, oil vapors, water, soap substances or due the inherent frictional characteristics of the tile material, surface design and texture, and Floor Surfaces does not assume any liability for any type of slippage by persons using its tiles used any conditions.

• In some applications, such as where there is concentrated sunlight, it may be required to glue tiles to the sub-floor.

8. Fire Resistance:

• PVC is a naturally fire resistant material
• Meets ASTM E648/NFPA 253 Critical Radiant Flux - Class 1

9. Installation:

See: Installation

1. Resilia Interlocking Floor Tile may be installed without adhesives on any firm, flat surface, using only a small roller, utility knife and common installation tools. Some applications, or a portion of a floor, may require tiles to be glued together or glued to the sub-floor.

2. The area to receive flooring should be weather-tight and maintained at a temperature between 60° F to 70° F for 48 hours prior to and during the installation.

3. The material must be maintained 60° F to 70° F for a minimum of 24 hours before starting the installation.

   Failure to maintain the tile at this temperature prior to installation may result in temporary variances in tile size. Also the installation may become difficult since floor tiles made from Flexible PVC, typically get harder as it get colder.

4. Resilia Floor Tile does not require adhesive and is designed to allow slight venting of water emission from floors. However some concrete floors have excessive moisture emission conditions that may cause potential microbial growth. In such cases existing flooring material and adhesive should be removed, and the concrete shot blasted to help prevent potential microbial growth problems, and then to apply a sealer designed to prevent microbial growth and resist moisture emission.

10. Availability:

Sold throughout North America directly by Floor Surfaces.

11. Installed Cost:

Installation is a simple and fast process and typically takes about 30 to 60 seconds per tile, plus trimming if required. Installed cost will vary based on local labor rates, job conditions complexity of the installation.

12. Warranty:

Floor Surfaces provides limited five (5) year warranty on its floor tile products.
See Floor Surfaces Warranty.

13. Maintenance:

Clean, hose or mop with water and any normal household cleaners.
See: Maintenance

14. Technical Support:

For samples, installation or technical assistance, contact Floor Surfaces, Inc. at: 805-275-4087 Monday through Friday 9:00 AM to 5:00PM PST.

Table 1 - Chemical Resistance

No Effect	Chemical Effect
Mineral Oil Turpentine Gasoline Kerosene Olive Oil Bleach Motor Oil Grease Transmission Fluid Brake Fluid Sulfuric Acid	Hydrochloric Acid 5% Acetic Acid 5% Isopropyl Alcohol 70% Sodium Hydroxide 5% Ammonia 5% Phenol 5% Methyl Ethyl Ketone (MEK) will dissolve PVC Acetone will mark and dull surface

Patents Pending

---